id
stringlengths 11
11
| images
listlengths 1
4
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_01552
|
[
"images/Shaft_01552.png",
"detail_png/Shaft_01552_length.png",
"detail_png/Shaft_01552_diam.png",
"detail_png/Shaft_01552_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.1 mm and length at least 178.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.1 mm over length 45.6 mm (from Z=0.0 to Z=45.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.8 mm over length 35.6 mm (from Z=0.0 to Z=127.8).\n9. Finish turn diameter Ø51.1 mm over length 26.5 mm (from Z=0.0 to Z=92.2).\n10. Finish turn diameter Ø39.0 mm over length 44.7 mm (from Z=0.0 to Z=65.7).\n11. Finish turn diameter Ø30.0 mm over length 21.0 mm (from Z=0.0 to Z=21.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03587
|
[
"images/Shaft_03587.png",
"detail_png/Shaft_03587_length.png",
"detail_png/Shaft_03587_diam.png",
"detail_png/Shaft_03587_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø78.1 mm and length at least 78.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.1 mm over length 19.6 mm (from Z=0.0 to Z=19.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø69.0 mm over length 19.1 mm (from Z=0.0 to Z=53.4).\n9. Finish turn diameter Ø53.9 mm over length 8.6 mm (from Z=0.0 to Z=34.3).\n10. Finish turn diameter Ø47.1 mm over length 25.7 mm (from Z=0.0 to Z=25.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00695
|
[
"images/Shaft_00695.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 155.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 99.0 mm (from Z=0.0 to Z=99.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.0 mm over length 51.9 mm (from Z=0.0 to Z=51.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03985
|
[
"images/Shaft_03985.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø37.0 mm and length at least 120.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.0 mm over length 23.4 mm (from Z=0.0 to Z=23.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 92.5 mm (from Z=0.0 to Z=92.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02943
|
[
"images/Shaft_02943.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 103.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 67.4 mm (from Z=0.0 to Z=67.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø24.3 mm over length 31.1 mm (from Z=0.0 to Z=31.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00874
|
[
"images/Shaft_00874.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø55.1 mm and length at least 203.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.1 mm over length 22.3 mm (from Z=0.0 to Z=22.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.2 mm over length 43.1 mm (from Z=0.0 to Z=176.6).\n10. Finish turn diameter Ø30.0 mm over length 133.5 mm (from Z=0.0 to Z=133.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04938
|
[
"images/Shaft_04938.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø38.1 mm and length at least 245.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.1 mm over length 43.2 mm (from Z=0.0 to Z=43.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.6 mm over length 36.5 mm (from Z=0.0 to Z=197.4).\n10. Finish turn diameter Ø30.0 mm over length 160.9 mm (from Z=0.0 to Z=160.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02448
|
[
"images/Shaft_02448.png",
"detail_png/Shaft_02448_length.png",
"detail_png/Shaft_02448_diam.png",
"detail_png/Shaft_02448_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø69.1 mm and length at least 85.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.1 mm over length 37.9 mm (from Z=0.0 to Z=37.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.9 mm over length 23.4 mm (from Z=0.0 to Z=42.5).\n9. Finish turn diameter Ø47.0 mm over length 19.1 mm (from Z=0.0 to Z=19.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01564
|
[
"images/Shaft_01564.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø61.5 mm and length at least 84.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.5 mm over length 19.6 mm (from Z=0.0 to Z=19.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.9 mm over length 8.5 mm (from Z=0.0 to Z=59.7).\n9. Finish turn diameter Ø47.5 mm over length 18.2 mm (from Z=0.0 to Z=51.2).\n10. Finish turn diameter Ø33.6 mm over length 5.6 mm (from Z=0.0 to Z=33.0).\n11. Finish turn diameter Ø30.0 mm over length 27.4 mm (from Z=0.0 to Z=27.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03147
|
[
"images/Shaft_03147.png",
"detail_png/Shaft_03147_length.png",
"detail_png/Shaft_03147_diam.png",
"detail_png/Shaft_03147_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø55.9 mm and length at least 250.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.9 mm over length 37.9 mm (from Z=0.0 to Z=37.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.8 mm over length 53.0 mm (from Z=0.0 to Z=207.7).\n10. Finish turn diameter Ø34.3 mm over length 81.4 mm (from Z=0.0 to Z=154.7).\n11. Finish turn diameter Ø30.0 mm over length 73.3 mm (from Z=0.0 to Z=73.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00322
|
[
"images/Shaft_00322.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø61.9 mm and length at least 288.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.9 mm over length 20.4 mm (from Z=0.0 to Z=20.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.8 mm over length 119.7 mm (from Z=0.0 to Z=262.6).\n10. Finish turn diameter Ø37.6 mm over length 110.3 mm (from Z=0.0 to Z=142.9).\n11. Finish turn diameter Ø32.2 mm over length 32.6 mm (from Z=0.0 to Z=32.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01446
|
[
"images/Shaft_01446.png",
"detail_png/Shaft_01446_length.png",
"detail_png/Shaft_01446_diam.png",
"detail_png/Shaft_01446_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø71.0 mm and length at least 85.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.0 mm over length 18.7 mm (from Z=0.0 to Z=18.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.4 mm over length 10.6 mm (from Z=0.0 to Z=62.2).\n9. Finish turn diameter Ø44.7 mm over length 6.0 mm (from Z=0.0 to Z=51.6).\n10. Finish turn diameter Ø34.7 mm over length 9.7 mm (from Z=0.0 to Z=45.6).\n11. Finish turn diameter Ø30.0 mm over length 35.9 mm (from Z=0.0 to Z=35.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01663
|
[
"images/Shaft_01663.png",
"detail_png/Shaft_01663_length.png",
"detail_png/Shaft_01663_diam.png",
"detail_png/Shaft_01663_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø47.8 mm and length at least 153.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.8 mm over length 60.5 mm (from Z=0.0 to Z=60.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø38.0 mm over length 21.8 mm (from Z=0.0 to Z=88.1).\n9. Finish turn diameter Ø30.0 mm over length 66.3 mm (from Z=0.0 to Z=66.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02375
|
[
"images/Shaft_02375.png",
"detail_png/Shaft_02375_length.png",
"detail_png/Shaft_02375_diam.png",
"detail_png/Shaft_02375_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø46.7 mm and length at least 151.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.7 mm over length 29.4 mm (from Z=0.0 to Z=29.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø41.1 mm over length 41.1 mm (from Z=0.0 to Z=116.7).\n9. Finish turn diameter Ø30.2 mm over length 30.5 mm (from Z=0.0 to Z=75.6).\n10. Finish turn diameter Ø30.0 mm over length 45.1 mm (from Z=0.0 to Z=45.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03765
|
[
"images/Shaft_03765.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø74.6 mm and length at least 177.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.6 mm over length 13.2 mm (from Z=0.0 to Z=13.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø66.7 mm over length 21.6 mm (from Z=0.0 to Z=159.5).\n9. Finish turn diameter Ø52.3 mm over length 47.9 mm (from Z=0.0 to Z=137.9).\n10. Finish turn diameter Ø37.6 mm over length 57.1 mm (from Z=0.0 to Z=90.0).\n11. Finish turn diameter Ø32.5 mm over length 23.9 mm (from Z=0.0 to Z=32.9).\n12. Finish turn diameter Ø30.0 mm over length 9.0 mm (from Z=0.0 to Z=9.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00659
|
[
"images/Shaft_00659.png",
"detail_png/Shaft_00659_length.png",
"detail_png/Shaft_00659_diam.png",
"detail_png/Shaft_00659_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.9 mm and length at least 311.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.9 mm over length 32.9 mm (from Z=0.0 to Z=32.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 273.7 mm (from Z=0.0 to Z=273.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02785
|
[
"images/Shaft_02785.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø59.0 mm and length at least 190.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.0 mm over length 53.0 mm (from Z=0.0 to Z=53.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.1 mm over length 71.1 mm (from Z=0.0 to Z=132.1).\n9. Finish turn diameter Ø33.2 mm over length 25.2 mm (from Z=0.0 to Z=61.0).\n10. Finish turn diameter Ø30.0 mm over length 35.8 mm (from Z=0.0 to Z=35.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04379
|
[
"images/Shaft_04379.png",
"detail_png/Shaft_04379_length.png",
"detail_png/Shaft_04379_diam.png",
"detail_png/Shaft_04379_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 121.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 98.6 mm (from Z=0.0 to Z=98.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø22.9 mm over length 17.9 mm (from Z=0.0 to Z=17.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02992
|
[
"images/Shaft_02992.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.2 mm and length at least 118.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.2 mm over length 62.5 mm (from Z=0.0 to Z=62.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.2 mm over length 29.4 mm (from Z=0.0 to Z=50.7).\n9. Finish turn diameter Ø41.2 mm over length 21.3 mm (from Z=0.0 to Z=21.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00742
|
[
"images/Shaft_00742.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.1 mm and length at least 67.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.1 mm over length 7.3 mm (from Z=0.0 to Z=7.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.1 mm over length 5.0 mm (from Z=0.0 to Z=55.0).\n9. Finish turn diameter Ø43.6 mm over length 11.9 mm (from Z=0.0 to Z=50.0).\n10. Finish turn diameter Ø30.0 mm over length 38.1 mm (from Z=0.0 to Z=38.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00452
|
[
"images/Shaft_00452.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø68.9 mm and length at least 275.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.9 mm over length 128.4 mm (from Z=0.0 to Z=128.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.9 mm over length 18.6 mm (from Z=0.0 to Z=141.7).\n10. Finish turn diameter Ø41.0 mm over length 90.1 mm (from Z=0.0 to Z=123.1).\n11. Finish turn diameter Ø30.0 mm over length 33.0 mm (from Z=0.0 to Z=33.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03281
|
[
"images/Shaft_03281.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø60.5 mm and length at least 203.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.5 mm over length 86.8 mm (from Z=0.0 to Z=86.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.1 mm over length 38.6 mm (from Z=0.0 to Z=111.3).\n10. Finish turn diameter Ø30.0 mm over length 72.7 mm (from Z=0.0 to Z=72.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02480
|
[
"images/Shaft_02480.png",
"detail_png/Shaft_02480_length.png",
"detail_png/Shaft_02480_diam.png",
"detail_png/Shaft_02480_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø58.8 mm and length at least 193.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.8 mm over length 56.5 mm (from Z=0.0 to Z=56.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.0 mm over length 34.5 mm (from Z=0.0 to Z=132.1).\n10. Finish turn diameter Ø30.0 mm over length 97.6 mm (from Z=0.0 to Z=97.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02731
|
[
"images/Shaft_02731.png",
"detail_png/Shaft_02731_length.png",
"detail_png/Shaft_02731_diam.png",
"detail_png/Shaft_02731_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.7 mm and length at least 70.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.7 mm over length 22.1 mm (from Z=0.0 to Z=22.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø45.7 mm over length 12.1 mm (from Z=0.0 to Z=43.5).\n9. Finish turn diameter Ø33.0 mm over length 6.7 mm (from Z=0.0 to Z=31.4).\n10. Finish turn diameter Ø30.0 mm over length 24.7 mm (from Z=0.0 to Z=24.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02940
|
[
"images/Shaft_02940.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø59.3 mm and length at least 141.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.3 mm over length 42.6 mm (from Z=0.0 to Z=42.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø48.4 mm over length 7.2 mm (from Z=0.0 to Z=94.3).\n9. Finish turn diameter Ø37.3 mm over length 17.9 mm (from Z=0.0 to Z=87.1).\n10. Finish turn diameter Ø30.0 mm over length 69.2 mm (from Z=0.0 to Z=69.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04385
|
[
"images/Shaft_04385.png",
"detail_png/Shaft_04385_length.png",
"detail_png/Shaft_04385_diam.png",
"detail_png/Shaft_04385_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø56.4 mm and length at least 289.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.4 mm over length 39.6 mm (from Z=0.0 to Z=39.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.7 mm over length 18.1 mm (from Z=0.0 to Z=244.8).\n10. Finish turn diameter Ø30.0 mm over length 226.7 mm (from Z=0.0 to Z=226.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00992
|
[
"images/Shaft_00992.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø38.5 mm and length at least 207.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.5 mm over length 44.4 mm (from Z=0.0 to Z=44.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 158.5 mm (from Z=0.0 to Z=158.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03949
|
[
"images/Shaft_03949.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø53.6 mm and length at least 146.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.6 mm over length 42.8 mm (from Z=0.0 to Z=42.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø41.5 mm over length 27.8 mm (from Z=0.0 to Z=99.0).\n9. Finish turn diameter Ø34.1 mm over length 55.7 mm (from Z=0.0 to Z=71.2).\n10. Finish turn diameter Ø30.0 mm over length 15.5 mm (from Z=0.0 to Z=15.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03149
|
[
"images/Shaft_03149.png",
"detail_png/Shaft_03149_length.png",
"detail_png/Shaft_03149_diam.png",
"detail_png/Shaft_03149_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø61.5 mm and length at least 103.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.5 mm over length 36.6 mm (from Z=0.0 to Z=36.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø48.2 mm over length 19.9 mm (from Z=0.0 to Z=61.6).\n9. Finish turn diameter Ø30.0 mm over length 41.7 mm (from Z=0.0 to Z=41.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00027
|
[
"images/Shaft_00027.png",
"detail_png/Shaft_00027_length.png",
"detail_png/Shaft_00027_diam.png",
"detail_png/Shaft_00027_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø43.7 mm and length at least 263.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.7 mm over length 50.9 mm (from Z=0.0 to Z=50.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.3 mm over length 46.7 mm (from Z=0.0 to Z=207.3).\n10. Finish turn diameter Ø30.0 mm over length 160.6 mm (from Z=0.0 to Z=160.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01850
|
[
"images/Shaft_01850.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø33.4 mm and length at least 140.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.4 mm over length 30.6 mm (from Z=0.0 to Z=30.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 105.1 mm (from Z=0.0 to Z=105.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04424
|
[
"images/Shaft_04424.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø68.2 mm and length at least 141.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.2 mm over length 55.8 mm (from Z=0.0 to Z=55.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.1 mm over length 23.8 mm (from Z=0.0 to Z=80.4).\n9. Finish turn diameter Ø42.4 mm over length 56.6 mm (from Z=0.0 to Z=56.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00574
|
[
"images/Shaft_00574.png",
"detail_png/Shaft_00574_length.png",
"detail_png/Shaft_00574_diam.png",
"detail_png/Shaft_00574_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø65.4 mm and length at least 323.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.4 mm over length 91.3 mm (from Z=0.0 to Z=91.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.5 mm over length 64.1 mm (from Z=0.0 to Z=227.1).\n10. Finish turn diameter Ø52.5 mm over length 51.4 mm (from Z=0.0 to Z=163.0).\n11. Finish turn diameter Ø43.9 mm over length 45.9 mm (from Z=0.0 to Z=111.6).\n12. Finish turn diameter Ø35.7 mm over length 65.7 mm (from Z=0.0 to Z=65.7).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_03308
|
[
"images/Shaft_03308.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 94.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 40.9 mm (from Z=0.0 to Z=40.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø29.5 mm over length 49.0 mm (from Z=0.0 to Z=49.0).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_03572
|
[
"images/Shaft_03572.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø74.3 mm and length at least 171.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.3 mm over length 84.4 mm (from Z=0.0 to Z=84.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø62.5 mm over length 21.5 mm (from Z=0.0 to Z=82.5).\n9. Finish turn diameter Ø42.7 mm over length 61.0 mm (from Z=0.0 to Z=61.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03916
|
[
"images/Shaft_03916.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø62.5 mm and length at least 287.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø60.5 mm over length 66.1 mm (from Z=0.0 to Z=66.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø60.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø49.3 mm over length 52.3 mm (from Z=0.0 to Z=216.6).\n10. Finish turn diameter Ø45.9 mm over length 43.0 mm (from Z=0.0 to Z=164.3).\n11. Finish turn diameter Ø33.9 mm over length 52.0 mm (from Z=0.0 to Z=121.3).\n12. Finish turn diameter Ø30.0 mm over length 69.3 mm (from Z=0.0 to Z=69.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_04019
|
[
"images/Shaft_04019.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø44.5 mm and length at least 241.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.5 mm over length 99.8 mm (from Z=0.0 to Z=99.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.0 mm over length 32.9 mm (from Z=0.0 to Z=136.4).\n10. Finish turn diameter Ø30.0 mm over length 103.5 mm (from Z=0.0 to Z=103.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04222
|
[
"images/Shaft_04222.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø75.2 mm and length at least 124.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.2 mm over length 51.0 mm (from Z=0.0 to Z=51.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø62.7 mm over length 43.5 mm (from Z=0.0 to Z=68.4).\n9. Finish turn diameter Ø50.4 mm over length 18.0 mm (from Z=0.0 to Z=24.9).\n10. Finish turn diameter Ø32.3 mm over length 6.9 mm (from Z=0.0 to Z=6.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00030
|
[
"images/Shaft_00030.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.3 mm and length at least 161.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.3 mm over length 25.8 mm (from Z=0.0 to Z=25.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.9 mm over length 58.4 mm (from Z=0.0 to Z=130.3).\n9. Finish turn diameter Ø33.1 mm over length 71.9 mm (from Z=0.0 to Z=71.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03205
|
[
"images/Shaft_03205.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø58.1 mm and length at least 127.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.1 mm over length 8.1 mm (from Z=0.0 to Z=8.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.8 mm over length 58.7 mm (from Z=0.0 to Z=114.7).\n9. Finish turn diameter Ø42.0 mm over length 27.4 mm (from Z=0.0 to Z=56.0).\n10. Finish turn diameter Ø35.5 mm over length 28.6 mm (from Z=0.0 to Z=28.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02701
|
[
"images/Shaft_02701.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø36.6 mm and length at least 231.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.6 mm over length 40.6 mm (from Z=0.0 to Z=40.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 186.3 mm (from Z=0.0 to Z=186.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01241
|
[
"images/Shaft_01241.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø50.3 mm and length at least 181.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.3 mm over length 13.6 mm (from Z=0.0 to Z=13.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.1 mm over length 40.9 mm (from Z=0.0 to Z=162.5).\n10. Finish turn diameter Ø30.0 mm over length 121.6 mm (from Z=0.0 to Z=121.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02182
|
[
"images/Shaft_02182.png",
"detail_png/Shaft_02182_length.png",
"detail_png/Shaft_02182_diam.png",
"detail_png/Shaft_02182_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø40.9 mm and length at least 247.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.9 mm over length 31.0 mm (from Z=0.0 to Z=31.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 211.9 mm (from Z=0.0 to Z=211.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03198
|
[
"images/Shaft_03198.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø68.5 mm and length at least 79.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.5 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.9 mm over length 38.6 mm (from Z=0.0 to Z=69.8).\n9. Finish turn diameter Ø31.3 mm over length 31.2 mm (from Z=0.0 to Z=31.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00309
|
[
"images/Shaft_00309.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø57.7 mm and length at least 253.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø55.7 mm over length 22.1 mm (from Z=0.0 to Z=22.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø55.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø50.0 mm over length 29.3 mm (from Z=0.0 to Z=226.3).\n10. Finish turn diameter Ø40.8 mm over length 36.7 mm (from Z=0.0 to Z=197.0).\n11. Finish turn diameter Ø36.4 mm over length 59.1 mm (from Z=0.0 to Z=160.3).\n12. Finish turn diameter Ø30.0 mm over length 101.2 mm (from Z=0.0 to Z=101.2).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00007
|
[
"images/Shaft_00007.png",
"detail_png/Shaft_00007_length.png",
"detail_png/Shaft_00007_diam.png",
"detail_png/Shaft_00007_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø33.0 mm and length at least 213.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.0 mm over length 24.1 mm (from Z=0.0 to Z=24.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 184.8 mm (from Z=0.0 to Z=184.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01219
|
[
"images/Shaft_01219.png",
"detail_png/Shaft_01219_length.png",
"detail_png/Shaft_01219_diam.png",
"detail_png/Shaft_01219_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø66.0 mm and length at least 312.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.0 mm over length 113.5 mm (from Z=0.0 to Z=113.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.6 mm over length 143.1 mm (from Z=0.0 to Z=194.3).\n10. Finish turn diameter Ø34.3 mm over length 33.4 mm (from Z=0.0 to Z=51.2).\n11. Finish turn diameter Ø30.0 mm over length 17.8 mm (from Z=0.0 to Z=17.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04995
|
[
"images/Shaft_04995.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 293.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 181.6 mm (from Z=0.0 to Z=181.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø18.7 mm over length 106.4 mm (from Z=0.0 to Z=106.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04936
|
[
"images/Shaft_04936.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 322.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 245.5 mm (from Z=0.0 to Z=245.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.1 mm over length 71.6 mm (from Z=0.0 to Z=71.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04815
|
[
"images/Shaft_04815.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø45.1 mm and length at least 288.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.1 mm over length 75.5 mm (from Z=0.0 to Z=75.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.6 mm over length 76.6 mm (from Z=0.0 to Z=207.6).\n10. Finish turn diameter Ø30.0 mm over length 131.0 mm (from Z=0.0 to Z=131.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02052
|
[
"images/Shaft_02052.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø59.5 mm and length at least 279.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.5 mm over length 29.0 mm (from Z=0.0 to Z=29.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.6 mm over length 124.8 mm (from Z=0.0 to Z=245.9).\n10. Finish turn diameter Ø32.2 mm over length 27.4 mm (from Z=0.0 to Z=121.1).\n11. Finish turn diameter Ø30.0 mm over length 93.7 mm (from Z=0.0 to Z=93.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00576
|
[
"images/Shaft_00576.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø43.9 mm and length at least 228.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.9 mm over length 53.9 mm (from Z=0.0 to Z=53.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 169.4 mm (from Z=0.0 to Z=169.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00597
|
[
"images/Shaft_00597.png",
"detail_png/Shaft_00597_length.png",
"detail_png/Shaft_00597_diam.png",
"detail_png/Shaft_00597_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 223.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 188.9 mm (from Z=0.0 to Z=188.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.8 mm over length 29.5 mm (from Z=0.0 to Z=29.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00285
|
[
"images/Shaft_00285.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø50.2 mm and length at least 287.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.2 mm over length 76.4 mm (from Z=0.0 to Z=76.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.9 mm over length 73.4 mm (from Z=0.0 to Z=206.0).\n10. Finish turn diameter Ø34.4 mm over length 84.3 mm (from Z=0.0 to Z=132.6).\n11. Finish turn diameter Ø30.0 mm over length 48.3 mm (from Z=0.0 to Z=48.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00846
|
[
"images/Shaft_00846.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø50.0 mm and length at least 99.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.0 mm over length 8.0 mm (from Z=0.0 to Z=8.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 86.4 mm (from Z=0.0 to Z=86.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_02121
|
[
"images/Shaft_02121.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø67.8 mm and length at least 102.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.8 mm over length 9.3 mm (from Z=0.0 to Z=9.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.6 mm over length 14.3 mm (from Z=0.0 to Z=87.7).\n9. Finish turn diameter Ø46.6 mm over length 11.4 mm (from Z=0.0 to Z=73.4).\n10. Finish turn diameter Ø37.5 mm over length 19.5 mm (from Z=0.0 to Z=62.0).\n11. Finish turn diameter Ø30.0 mm over length 42.5 mm (from Z=0.0 to Z=42.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03617
|
[
"images/Shaft_03617.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.9 mm and length at least 254.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.9 mm over length 48.1 mm (from Z=0.0 to Z=48.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.1 mm over length 40.1 mm (from Z=0.0 to Z=201.3).\n10. Finish turn diameter Ø36.0 mm over length 38.3 mm (from Z=0.0 to Z=161.2).\n11. Finish turn diameter Ø30.0 mm over length 122.9 mm (from Z=0.0 to Z=122.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00870
|
[
"images/Shaft_00870.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø59.2 mm and length at least 88.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.2 mm over length 10.9 mm (from Z=0.0 to Z=10.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.7 mm over length 28.2 mm (from Z=0.0 to Z=72.8).\n9. Finish turn diameter Ø37.0 mm over length 44.6 mm (from Z=0.0 to Z=44.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01789
|
[
"images/Shaft_01789.png",
"detail_png/Shaft_01789_length.png",
"detail_png/Shaft_01789_diam.png",
"detail_png/Shaft_01789_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø34.0 mm and length at least 128.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.0 mm over length 17.0 mm (from Z=0.0 to Z=17.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 106.5 mm (from Z=0.0 to Z=106.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03532
|
[
"images/Shaft_03532.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 319.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 252.3 mm (from Z=0.0 to Z=252.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.6 mm over length 62.1 mm (from Z=0.0 to Z=62.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04829
|
[
"images/Shaft_04829.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 121.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 75.5 mm (from Z=0.0 to Z=75.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø21.2 mm over length 41.2 mm (from Z=0.0 to Z=41.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_01178
|
[
"images/Shaft_01178.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø54.8 mm and length at least 164.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.8 mm over length 39.1 mm (from Z=0.0 to Z=39.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø48.4 mm over length 16.8 mm (from Z=0.0 to Z=119.9).\n9. Finish turn diameter Ø40.5 mm over length 25.9 mm (from Z=0.0 to Z=103.1).\n10. Finish turn diameter Ø30.0 mm over length 77.2 mm (from Z=0.0 to Z=77.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00888
|
[
"images/Shaft_00888.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.6 mm and length at least 242.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.6 mm over length 45.9 mm (from Z=0.0 to Z=45.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø63.5 mm over length 12.6 mm (from Z=0.0 to Z=191.9).\n10. Finish turn diameter Ø51.8 mm over length 15.1 mm (from Z=0.0 to Z=179.3).\n11. Finish turn diameter Ø43.3 mm over length 63.9 mm (from Z=0.0 to Z=164.2).\n12. Finish turn diameter Ø31.2 mm over length 35.3 mm (from Z=0.0 to Z=100.3).\n13. Finish turn diameter Ø30.0 mm over length 65.0 mm (from Z=0.0 to Z=65.0).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_04030
|
[
"images/Shaft_04030.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø44.0 mm and length at least 305.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.0 mm over length 41.8 mm (from Z=0.0 to Z=41.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 258.9 mm (from Z=0.0 to Z=258.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01461
|
[
"images/Shaft_01461.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø76.4 mm and length at least 315.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.4 mm over length 81.8 mm (from Z=0.0 to Z=81.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø71.2 mm over length 90.8 mm (from Z=0.0 to Z=228.7).\n10. Finish turn diameter Ø65.8 mm over length 137.9 mm (from Z=0.0 to Z=137.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03216
|
[
"images/Shaft_03216.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø80.0 mm and length at least 122.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.0 mm over length 17.9 mm (from Z=0.0 to Z=17.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø73.5 mm over length 35.1 mm (from Z=0.0 to Z=100.0).\n9. Finish turn diameter Ø58.1 mm over length 14.8 mm (from Z=0.0 to Z=64.9).\n10. Finish turn diameter Ø43.8 mm over length 13.9 mm (from Z=0.0 to Z=50.1).\n11. Finish turn diameter Ø36.9 mm over length 31.2 mm (from Z=0.0 to Z=36.2).\n12. Finish turn diameter Ø30.8 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_01643
|
[
"images/Shaft_01643.png",
"detail_png/Shaft_01643_length.png",
"detail_png/Shaft_01643_diam.png",
"detail_png/Shaft_01643_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø54.1 mm and length at least 246.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.1 mm over length 36.3 mm (from Z=0.0 to Z=36.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø48.5 mm over length 37.2 mm (from Z=0.0 to Z=205.5).\n10. Finish turn diameter Ø42.6 mm over length 19.9 mm (from Z=0.0 to Z=168.3).\n11. Finish turn diameter Ø30.7 mm over length 44.1 mm (from Z=0.0 to Z=148.4).\n12. Finish turn diameter Ø30.0 mm over length 104.3 mm (from Z=0.0 to Z=104.3).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_04028
|
[
"images/Shaft_04028.png",
"detail_png/Shaft_04028_length.png",
"detail_png/Shaft_04028_diam.png",
"detail_png/Shaft_04028_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø67.5 mm and length at least 207.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.5 mm over length 15.0 mm (from Z=0.0 to Z=15.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø55.0 mm over length 66.8 mm (from Z=0.0 to Z=187.7).\n10. Finish turn diameter Ø43.6 mm over length 47.1 mm (from Z=0.0 to Z=120.9).\n11. Finish turn diameter Ø37.2 mm over length 31.9 mm (from Z=0.0 to Z=73.8).\n12. Finish turn diameter Ø30.0 mm over length 41.9 mm (from Z=0.0 to Z=41.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00568
|
[
"images/Shaft_00568.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø45.6 mm and length at least 66.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.6 mm over length 14.6 mm (from Z=0.0 to Z=14.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø31.4 mm over length 21.1 mm (from Z=0.0 to Z=46.9).\n9. Finish turn diameter Ø30.0 mm over length 25.8 mm (from Z=0.0 to Z=25.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03609
|
[
"images/Shaft_03609.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø76.4 mm and length at least 238.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.4 mm over length 39.5 mm (from Z=0.0 to Z=39.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø70.6 mm over length 51.3 mm (from Z=0.0 to Z=194.0).\n10. Finish turn diameter Ø63.3 mm over length 119.1 mm (from Z=0.0 to Z=142.7).\n11. Finish turn diameter Ø57.5 mm over length 23.6 mm (from Z=0.0 to Z=23.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01457
|
[
"images/Shaft_01457.png",
"detail_png/Shaft_01457_length.png",
"detail_png/Shaft_01457_diam.png",
"detail_png/Shaft_01457_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø56.4 mm and length at least 69.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.4 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.8 mm over length 18.5 mm (from Z=0.0 to Z=59.0).\n9. Finish turn diameter Ø30.2 mm over length 15.8 mm (from Z=0.0 to Z=40.5).\n10. Finish turn diameter Ø30.0 mm over length 24.7 mm (from Z=0.0 to Z=24.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02168
|
[
"images/Shaft_02168.png",
"detail_png/Shaft_02168_length.png",
"detail_png/Shaft_02168_diam.png",
"detail_png/Shaft_02168_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 104.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 74.0 mm (from Z=0.0 to Z=74.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø21.6 mm over length 25.4 mm (from Z=0.0 to Z=25.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_02115
|
[
"images/Shaft_02115.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø67.8 mm and length at least 89.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.8 mm over length 13.3 mm (from Z=0.0 to Z=13.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.2 mm over length 35.7 mm (from Z=0.0 to Z=70.7).\n9. Finish turn diameter Ø42.9 mm over length 35.0 mm (from Z=0.0 to Z=35.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00492
|
[
"images/Shaft_00492.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø54.5 mm and length at least 203.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.5 mm over length 40.0 mm (from Z=0.0 to Z=40.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.4 mm over length 44.9 mm (from Z=0.0 to Z=158.7).\n10. Finish turn diameter Ø30.0 mm over length 113.8 mm (from Z=0.0 to Z=113.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02725
|
[
"images/Shaft_02725.png",
"detail_png/Shaft_02725_length.png",
"detail_png/Shaft_02725_diam.png",
"detail_png/Shaft_02725_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 275.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 214.2 mm (from Z=0.0 to Z=214.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.5 mm over length 56.4 mm (from Z=0.0 to Z=56.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03183
|
[
"images/Shaft_03183.png",
"detail_png/Shaft_03183_length.png",
"detail_png/Shaft_03183_diam.png",
"detail_png/Shaft_03183_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø60.4 mm and length at least 123.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø58.4 mm over length 22.4 mm (from Z=0.0 to Z=22.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø58.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.5 mm over length 36.3 mm (from Z=0.0 to Z=96.3).\n9. Finish turn diameter Ø30.0 mm over length 60.0 mm (from Z=0.0 to Z=60.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04690
|
[
"images/Shaft_04690.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø41.4 mm and length at least 316.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.4 mm over length 52.1 mm (from Z=0.0 to Z=52.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 259.7 mm (from Z=0.0 to Z=259.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04704
|
[
"images/Shaft_04704.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø44.4 mm and length at least 232.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.4 mm over length 40.9 mm (from Z=0.0 to Z=40.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 186.4 mm (from Z=0.0 to Z=186.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02271
|
[
"images/Shaft_02271.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 91.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 73.4 mm (from Z=0.0 to Z=73.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø26.8 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00606
|
[
"images/Shaft_00606.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 205.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 100.5 mm (from Z=0.0 to Z=100.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø18.8 mm over length 99.9 mm (from Z=0.0 to Z=99.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01326
|
[
"images/Shaft_01326.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø47.9 mm and length at least 116.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.9 mm over length 22.3 mm (from Z=0.0 to Z=22.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø34.4 mm over length 7.9 mm (from Z=0.0 to Z=89.4).\n9. Finish turn diameter Ø30.0 mm over length 81.5 mm (from Z=0.0 to Z=81.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02108
|
[
"images/Shaft_02108.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.2 mm and length at least 171.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.2 mm over length 8.6 mm (from Z=0.0 to Z=8.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.6 mm over length 26.2 mm (from Z=0.0 to Z=158.0).\n9. Finish turn diameter Ø37.2 mm over length 66.7 mm (from Z=0.0 to Z=131.8).\n10. Finish turn diameter Ø30.0 mm over length 65.1 mm (from Z=0.0 to Z=65.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02649
|
[
"images/Shaft_02649.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø63.1 mm and length at least 178.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.1 mm over length 25.5 mm (from Z=0.0 to Z=25.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.0 mm over length 71.3 mm (from Z=0.0 to Z=147.7).\n9. Finish turn diameter Ø30.0 mm over length 76.4 mm (from Z=0.0 to Z=76.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03497
|
[
"images/Shaft_03497.png",
"detail_png/Shaft_03497_length.png",
"detail_png/Shaft_03497_diam.png",
"detail_png/Shaft_03497_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 135.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 117.4 mm (from Z=0.0 to Z=117.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.4 mm over length 13.3 mm (from Z=0.0 to Z=13.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02264
|
[
"images/Shaft_02264.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø77.9 mm and length at least 89.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.9 mm over length 27.9 mm (from Z=0.0 to Z=27.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.4 mm over length 9.3 mm (from Z=0.0 to Z=56.4).\n9. Finish turn diameter Ø41.9 mm over length 9.7 mm (from Z=0.0 to Z=47.1).\n10. Finish turn diameter Ø30.0 mm over length 37.4 mm (from Z=0.0 to Z=37.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03714
|
[
"images/Shaft_03714.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.9 mm and length at least 168.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.9 mm over length 16.5 mm (from Z=0.0 to Z=16.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.6 mm over length 61.9 mm (from Z=0.0 to Z=147.1).\n9. Finish turn diameter Ø48.4 mm over length 26.9 mm (from Z=0.0 to Z=85.2).\n10. Finish turn diameter Ø40.1 mm over length 19.5 mm (from Z=0.0 to Z=58.3).\n11. Finish turn diameter Ø30.0 mm over length 38.8 mm (from Z=0.0 to Z=38.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00620
|
[
"images/Shaft_00620.png",
"detail_png/Shaft_00620_length.png",
"detail_png/Shaft_00620_diam.png",
"detail_png/Shaft_00620_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 68.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 45.3 mm (from Z=0.0 to Z=45.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø18.6 mm over length 18.1 mm (from Z=0.0 to Z=18.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_03825
|
[
"images/Shaft_03825.png",
"detail_png/Shaft_03825_length.png",
"detail_png/Shaft_03825_diam.png",
"detail_png/Shaft_03825_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø39.5 mm and length at least 241.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.5 mm over length 32.2 mm (from Z=0.0 to Z=32.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 203.8 mm (from Z=0.0 to Z=203.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04610
|
[
"images/Shaft_04610.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø61.8 mm and length at least 80.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.8 mm over length 6.0 mm (from Z=0.0 to Z=6.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø44.3 mm over length 17.1 mm (from Z=0.0 to Z=69.7).\n9. Finish turn diameter Ø30.0 mm over length 52.6 mm (from Z=0.0 to Z=52.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02075
|
[
"images/Shaft_02075.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø64.2 mm and length at least 276.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.2 mm over length 55.2 mm (from Z=0.0 to Z=55.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.8 mm over length 65.1 mm (from Z=0.0 to Z=216.6).\n10. Finish turn diameter Ø30.0 mm over length 151.5 mm (from Z=0.0 to Z=151.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01509
|
[
"images/Shaft_01509.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 72.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 48.4 mm (from Z=0.0 to Z=48.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø26.1 mm over length 19.3 mm (from Z=0.0 to Z=19.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00908
|
[
"images/Shaft_00908.png",
"detail_png/Shaft_00908_length.png",
"detail_png/Shaft_00908_diam.png",
"detail_png/Shaft_00908_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø47.9 mm and length at least 112.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.9 mm over length 22.8 mm (from Z=0.0 to Z=22.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.6 mm over length 8.9 mm (from Z=0.0 to Z=84.5).\n9. Finish turn diameter Ø30.0 mm over length 75.6 mm (from Z=0.0 to Z=75.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01513
|
[
"images/Shaft_01513.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø48.9 mm and length at least 243.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.9 mm over length 59.8 mm (from Z=0.0 to Z=59.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø31.5 mm over length 11.9 mm (from Z=0.0 to Z=179.1).\n10. Finish turn diameter Ø30.0 mm over length 167.2 mm (from Z=0.0 to Z=167.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03079
|
[
"images/Shaft_03079.png",
"detail_png/Shaft_03079_length.png",
"detail_png/Shaft_03079_diam.png",
"detail_png/Shaft_03079_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 214.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 178.8 mm (from Z=0.0 to Z=178.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.5 mm over length 30.6 mm (from Z=0.0 to Z=30.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01064
|
[
"images/Shaft_01064.png",
"detail_png/Shaft_01064_length.png",
"detail_png/Shaft_01064_diam.png",
"detail_png/Shaft_01064_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø45.5 mm and length at least 122.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.5 mm over length 21.3 mm (from Z=0.0 to Z=21.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø31.8 mm over length 29.9 mm (from Z=0.0 to Z=95.9).\n9. Finish turn diameter Ø30.0 mm over length 66.0 mm (from Z=0.0 to Z=66.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00707
|
[
"images/Shaft_00707.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø71.5 mm and length at least 187.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.5 mm over length 10.5 mm (from Z=0.0 to Z=10.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.0 mm over length 28.9 mm (from Z=0.0 to Z=172.3).\n9. Finish turn diameter Ø56.9 mm over length 87.3 mm (from Z=0.0 to Z=143.4).\n10. Finish turn diameter Ø44.1 mm over length 56.1 mm (from Z=0.0 to Z=56.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00982
|
[
"images/Shaft_00982.png",
"detail_png/Shaft_00982_length.png",
"detail_png/Shaft_00982_diam.png",
"detail_png/Shaft_00982_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø81.9 mm and length at least 145.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.9 mm over length 35.7 mm (from Z=0.0 to Z=35.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø68.8 mm over length 33.4 mm (from Z=0.0 to Z=104.6).\n9. Finish turn diameter Ø54.4 mm over length 29.8 mm (from Z=0.0 to Z=71.2).\n10. Finish turn diameter Ø39.2 mm over length 41.4 mm (from Z=0.0 to Z=41.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00997
|
[
"images/Shaft_00997.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø74.8 mm and length at least 292.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.8 mm over length 96.4 mm (from Z=0.0 to Z=96.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.7 mm over length 77.3 mm (from Z=0.0 to Z=190.9).\n10. Finish turn diameter Ø47.1 mm over length 77.6 mm (from Z=0.0 to Z=113.6).\n11. Finish turn diameter Ø38.0 mm over length 36.0 mm (from Z=0.0 to Z=36.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01776
|
[
"images/Shaft_01776.png",
"detail_png/Shaft_01776_length.png",
"detail_png/Shaft_01776_diam.png",
"detail_png/Shaft_01776_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 306.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 145.6 mm (from Z=0.0 to Z=145.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø20.1 mm over length 155.5 mm (from Z=0.0 to Z=155.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00465
|
[
"images/Shaft_00465.png",
"detail_png/Shaft_00465_length.png",
"detail_png/Shaft_00465_diam.png",
"detail_png/Shaft_00465_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.5 mm and length at least 209.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.5 mm over length 100.8 mm (from Z=0.0 to Z=100.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.4 mm over length 22.4 mm (from Z=0.0 to Z=104.1).\n10. Finish turn diameter Ø57.9 mm over length 12.2 mm (from Z=0.0 to Z=81.7).\n11. Finish turn diameter Ø51.5 mm over length 52.4 mm (from Z=0.0 to Z=69.5).\n12. Finish turn diameter Ø31.5 mm over length 17.1 mm (from Z=0.0 to Z=17.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.