id
stringlengths 11
11
| images
listlengths 1
4
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_04706
|
[
"images/Shaft_04706.png",
"detail_png/Shaft_04706_length.png",
"detail_png/Shaft_04706_diam.png",
"detail_png/Shaft_04706_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø43.0 mm and length at least 90.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.0 mm over length 6.4 mm (from Z=0.0 to Z=6.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø36.3 mm over length 7.0 mm (from Z=0.0 to Z=78.6).\n9. Finish turn diameter Ø30.0 mm over length 71.6 mm (from Z=0.0 to Z=71.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01583
|
[
"images/Shaft_01583.png",
"detail_png/Shaft_01583_length.png",
"detail_png/Shaft_01583_diam.png",
"detail_png/Shaft_01583_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø74.2 mm and length at least 103.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.2 mm over length 15.5 mm (from Z=0.0 to Z=15.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø67.1 mm over length 39.6 mm (from Z=0.0 to Z=82.8).\n9. Finish turn diameter Ø47.4 mm over length 43.2 mm (from Z=0.0 to Z=43.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01651
|
[
"images/Shaft_01651.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø42.1 mm and length at least 101.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.1 mm over length 18.9 mm (from Z=0.0 to Z=18.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 77.8 mm (from Z=0.0 to Z=77.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00719
|
[
"images/Shaft_00719.png",
"detail_png/Shaft_00719_length.png",
"detail_png/Shaft_00719_diam.png",
"detail_png/Shaft_00719_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø77.6 mm and length at least 129.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.6 mm over length 49.0 mm (from Z=0.0 to Z=49.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø57.2 mm over length 38.3 mm (from Z=0.0 to Z=75.8).\n9. Finish turn diameter Ø44.0 mm over length 37.5 mm (from Z=0.0 to Z=37.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01549
|
[
"images/Shaft_01549.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.3 mm and length at least 279.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.3 mm over length 56.4 mm (from Z=0.0 to Z=56.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 217.6 mm (from Z=0.0 to Z=217.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02053
|
[
"images/Shaft_02053.png",
"detail_png/Shaft_02053_length.png",
"detail_png/Shaft_02053_diam.png",
"detail_png/Shaft_02053_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø73.1 mm and length at least 156.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.1 mm over length 42.3 mm (from Z=0.0 to Z=42.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø60.1 mm over length 51.6 mm (from Z=0.0 to Z=108.7).\n9. Finish turn diameter Ø44.0 mm over length 57.1 mm (from Z=0.0 to Z=57.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01670
|
[
"images/Shaft_01670.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 254.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 207.5 mm (from Z=0.0 to Z=207.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.6 mm over length 41.8 mm (from Z=0.0 to Z=41.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00714
|
[
"images/Shaft_00714.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 223.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 167.9 mm (from Z=0.0 to Z=167.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.7 mm over length 50.5 mm (from Z=0.0 to Z=50.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00706
|
[
"images/Shaft_00706.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø44.5 mm and length at least 174.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.5 mm over length 63.8 mm (from Z=0.0 to Z=63.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø33.7 mm over length 12.2 mm (from Z=0.0 to Z=105.5).\n10. Finish turn diameter Ø30.0 mm over length 93.3 mm (from Z=0.0 to Z=93.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01851
|
[
"images/Shaft_01851.png",
"detail_png/Shaft_01851_length.png",
"detail_png/Shaft_01851_diam.png",
"detail_png/Shaft_01851_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø51.2 mm and length at least 210.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.2 mm over length 89.0 mm (from Z=0.0 to Z=89.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.5 mm over length 100.0 mm (from Z=0.0 to Z=116.1).\n10. Finish turn diameter Ø30.0 mm over length 16.1 mm (from Z=0.0 to Z=16.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00847
|
[
"images/Shaft_00847.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø63.7 mm and length at least 253.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.7 mm over length 34.0 mm (from Z=0.0 to Z=34.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø51.0 mm over length 26.4 mm (from Z=0.0 to Z=214.3).\n10. Finish turn diameter Ø39.0 mm over length 95.3 mm (from Z=0.0 to Z=187.9).\n11. Finish turn diameter Ø30.0 mm over length 92.6 mm (from Z=0.0 to Z=92.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01337
|
[
"images/Shaft_01337.png",
"detail_png/Shaft_01337_length.png",
"detail_png/Shaft_01337_diam.png",
"detail_png/Shaft_01337_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø44.6 mm and length at least 300.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.6 mm over length 82.0 mm (from Z=0.0 to Z=82.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.6 mm over length 31.8 mm (from Z=0.0 to Z=213.9).\n10. Finish turn diameter Ø30.0 mm over length 182.1 mm (from Z=0.0 to Z=182.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03558
|
[
"images/Shaft_03558.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø37.5 mm and length at least 131.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.5 mm over length 52.3 mm (from Z=0.0 to Z=52.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 74.0 mm (from Z=0.0 to Z=74.0).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_01319
|
[
"images/Shaft_01319.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.4 mm and length at least 65.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.4 mm over length 37.3 mm (from Z=0.0 to Z=37.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø67.7 mm over length 11.3 mm (from Z=0.0 to Z=23.4).\n9. Finish turn diameter Ø62.1 mm over length 12.1 mm (from Z=0.0 to Z=12.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04036
|
[
"images/Shaft_04036.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø63.9 mm and length at least 175.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.9 mm over length 24.7 mm (from Z=0.0 to Z=24.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø49.9 mm over length 43.1 mm (from Z=0.0 to Z=145.3).\n9. Finish turn diameter Ø33.5 mm over length 45.2 mm (from Z=0.0 to Z=102.2).\n10. Finish turn diameter Ø30.0 mm over length 57.0 mm (from Z=0.0 to Z=57.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04251
|
[
"images/Shaft_04251.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø33.6 mm and length at least 158.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.6 mm over length 46.0 mm (from Z=0.0 to Z=46.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 107.1 mm (from Z=0.0 to Z=107.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01224
|
[
"images/Shaft_01224.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø64.4 mm and length at least 227.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.4 mm over length 76.0 mm (from Z=0.0 to Z=76.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø49.4 mm over length 31.1 mm (from Z=0.0 to Z=146.4).\n10. Finish turn diameter Ø46.2 mm over length 80.9 mm (from Z=0.0 to Z=115.3).\n11. Finish turn diameter Ø30.0 mm over length 34.4 mm (from Z=0.0 to Z=34.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_02085
|
[
"images/Shaft_02085.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø54.9 mm and length at least 249.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.9 mm over length 95.0 mm (from Z=0.0 to Z=95.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.7 mm over length 66.8 mm (from Z=0.0 to Z=149.0).\n10. Finish turn diameter Ø30.0 mm over length 82.2 mm (from Z=0.0 to Z=82.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04299
|
[
"images/Shaft_04299.png",
"detail_png/Shaft_04299_length.png",
"detail_png/Shaft_04299_diam.png",
"detail_png/Shaft_04299_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø66.4 mm and length at least 124.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø64.4 mm over length 19.9 mm (from Z=0.0 to Z=19.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø64.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.7 mm over length 74.7 mm (from Z=0.0 to Z=99.6).\n9. Finish turn diameter Ø47.6 mm over length 24.9 mm (from Z=0.0 to Z=24.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04037
|
[
"images/Shaft_04037.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø70.5 mm and length at least 195.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.5 mm over length 37.1 mm (from Z=0.0 to Z=37.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø54.9 mm over length 28.6 mm (from Z=0.0 to Z=153.3).\n10. Finish turn diameter Ø35.6 mm over length 29.5 mm (from Z=0.0 to Z=124.7).\n11. Finish turn diameter Ø30.0 mm over length 95.2 mm (from Z=0.0 to Z=95.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00045
|
[
"images/Shaft_00045.png",
"detail_png/Shaft_00045_length.png",
"detail_png/Shaft_00045_diam.png",
"detail_png/Shaft_00045_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø43.9 mm and length at least 181.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.9 mm over length 23.9 mm (from Z=0.0 to Z=23.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 152.9 mm (from Z=0.0 to Z=152.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01198
|
[
"images/Shaft_01198.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø44.9 mm and length at least 97.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.9 mm over length 27.0 mm (from Z=0.0 to Z=27.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 65.0 mm (from Z=0.0 to Z=65.0).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_02021
|
[
"images/Shaft_02021.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.2 mm and length at least 209.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.2 mm over length 53.8 mm (from Z=0.0 to Z=53.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.6 mm over length 71.7 mm (from Z=0.0 to Z=150.5).\n10. Finish turn diameter Ø44.0 mm over length 78.8 mm (from Z=0.0 to Z=78.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01755
|
[
"images/Shaft_01755.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø74.3 mm and length at least 108.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.3 mm over length 28.3 mm (from Z=0.0 to Z=28.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø66.1 mm over length 23.6 mm (from Z=0.0 to Z=74.9).\n9. Finish turn diameter Ø56.0 mm over length 51.3 mm (from Z=0.0 to Z=51.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02415
|
[
"images/Shaft_02415.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.6 mm and length at least 323.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.6 mm over length 93.8 mm (from Z=0.0 to Z=93.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø67.7 mm over length 115.7 mm (from Z=0.0 to Z=225.0).\n10. Finish turn diameter Ø63.7 mm over length 73.3 mm (from Z=0.0 to Z=109.3).\n11. Finish turn diameter Ø49.1 mm over length 22.4 mm (from Z=0.0 to Z=36.0).\n12. Finish turn diameter Ø31.3 mm over length 13.6 mm (from Z=0.0 to Z=13.6).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_04017
|
[
"images/Shaft_04017.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø42.3 mm and length at least 307.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.3 mm over length 64.6 mm (from Z=0.0 to Z=64.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 238.0 mm (from Z=0.0 to Z=238.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03469
|
[
"images/Shaft_03469.png",
"detail_png/Shaft_03469_length.png",
"detail_png/Shaft_03469_diam.png",
"detail_png/Shaft_03469_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø75.7 mm and length at least 228.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.7 mm over length 37.4 mm (from Z=0.0 to Z=37.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.6 mm over length 55.7 mm (from Z=0.0 to Z=186.2).\n10. Finish turn diameter Ø44.0 mm over length 35.9 mm (from Z=0.0 to Z=130.5).\n11. Finish turn diameter Ø32.3 mm over length 58.0 mm (from Z=0.0 to Z=94.6).\n12. Finish turn diameter Ø30.0 mm over length 36.6 mm (from Z=0.0 to Z=36.6).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_03980
|
[
"images/Shaft_03980.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 299.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 160.7 mm (from Z=0.0 to Z=160.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.2 mm over length 133.7 mm (from Z=0.0 to Z=133.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04580
|
[
"images/Shaft_04580.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø55.9 mm and length at least 212.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.9 mm over length 92.9 mm (from Z=0.0 to Z=92.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.0 mm over length 21.5 mm (from Z=0.0 to Z=114.7).\n10. Finish turn diameter Ø30.0 mm over length 93.2 mm (from Z=0.0 to Z=93.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03917
|
[
"images/Shaft_03917.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 156.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 84.4 mm (from Z=0.0 to Z=84.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø24.0 mm over length 67.2 mm (from Z=0.0 to Z=67.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_04758
|
[
"images/Shaft_04758.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø42.7 mm and length at least 79.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.7 mm over length 13.5 mm (from Z=0.0 to Z=13.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 61.3 mm (from Z=0.0 to Z=61.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00307
|
[
"images/Shaft_00307.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø69.3 mm and length at least 249.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.3 mm over length 52.3 mm (from Z=0.0 to Z=52.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø57.9 mm over length 15.6 mm (from Z=0.0 to Z=191.8).\n10. Finish turn diameter Ø41.9 mm over length 55.4 mm (from Z=0.0 to Z=176.2).\n11. Finish turn diameter Ø34.8 mm over length 16.8 mm (from Z=0.0 to Z=120.8).\n12. Finish turn diameter Ø30.1 mm over length 31.5 mm (from Z=0.0 to Z=104.0).\n13. Finish turn diameter Ø30.0 mm over length 72.5 mm (from Z=0.0 to Z=72.5).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_04844
|
[
"images/Shaft_04844.png",
"detail_png/Shaft_04844_length.png",
"detail_png/Shaft_04844_diam.png",
"detail_png/Shaft_04844_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø42.8 mm and length at least 69.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø40.8 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø40.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø36.9 mm over length 12.7 mm (from Z=0.0 to Z=59.3).\n9. Finish turn diameter Ø30.0 mm over length 46.6 mm (from Z=0.0 to Z=46.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00000
|
[
"images/Shaft_00000.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø74.7 mm and length at least 238.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.7 mm over length 22.3 mm (from Z=0.0 to Z=22.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø63.6 mm over length 58.3 mm (from Z=0.0 to Z=210.9).\n10. Finish turn diameter Ø46.8 mm over length 52.1 mm (from Z=0.0 to Z=152.6).\n11. Finish turn diameter Ø30.0 mm over length 100.5 mm (from Z=0.0 to Z=100.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03238
|
[
"images/Shaft_03238.png",
"detail_png/Shaft_03238_length.png",
"detail_png/Shaft_03238_diam.png",
"detail_png/Shaft_03238_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø64.8 mm and length at least 320.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.8 mm over length 40.1 mm (from Z=0.0 to Z=40.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.5 mm over length 11.6 mm (from Z=0.0 to Z=275.4).\n10. Finish turn diameter Ø41.2 mm over length 76.0 mm (from Z=0.0 to Z=263.8).\n11. Finish turn diameter Ø31.3 mm over length 81.9 mm (from Z=0.0 to Z=187.8).\n12. Finish turn diameter Ø30.0 mm over length 105.9 mm (from Z=0.0 to Z=105.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_03374
|
[
"images/Shaft_03374.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø79.0 mm and length at least 263.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.0 mm over length 89.8 mm (from Z=0.0 to Z=89.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø66.2 mm over length 57.6 mm (from Z=0.0 to Z=168.9).\n10. Finish turn diameter Ø48.5 mm over length 63.7 mm (from Z=0.0 to Z=111.3).\n11. Finish turn diameter Ø41.9 mm over length 47.6 mm (from Z=0.0 to Z=47.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_02181
|
[
"images/Shaft_02181.png",
"detail_png/Shaft_02181_length.png",
"detail_png/Shaft_02181_diam.png",
"detail_png/Shaft_02181_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 295.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 223.3 mm (from Z=0.0 to Z=223.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.9 mm over length 67.1 mm (from Z=0.0 to Z=67.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02361
|
[
"images/Shaft_02361.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.5 mm and length at least 274.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.5 mm over length 45.7 mm (from Z=0.0 to Z=45.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø45.6 mm over length 59.8 mm (from Z=0.0 to Z=223.3).\n10. Finish turn diameter Ø39.6 mm over length 43.1 mm (from Z=0.0 to Z=163.5).\n11. Finish turn diameter Ø30.0 mm over length 120.4 mm (from Z=0.0 to Z=120.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04003
|
[
"images/Shaft_04003.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 281.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 237.0 mm (from Z=0.0 to Z=237.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.3 mm over length 39.5 mm (from Z=0.0 to Z=39.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02536
|
[
"images/Shaft_02536.png",
"detail_png/Shaft_02536_length.png",
"detail_png/Shaft_02536_diam.png",
"detail_png/Shaft_02536_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø55.6 mm and length at least 162.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.6 mm over length 13.2 mm (from Z=0.0 to Z=13.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø40.5 mm over length 47.3 mm (from Z=0.0 to Z=144.7).\n10. Finish turn diameter Ø30.0 mm over length 97.4 mm (from Z=0.0 to Z=97.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03377
|
[
"images/Shaft_03377.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø78.4 mm and length at least 179.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.4 mm over length 64.1 mm (from Z=0.0 to Z=64.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø68.8 mm over length 6.2 mm (from Z=0.0 to Z=110.2).\n9. Finish turn diameter Ø61.2 mm over length 50.9 mm (from Z=0.0 to Z=104.0).\n10. Finish turn diameter Ø51.7 mm over length 17.1 mm (from Z=0.0 to Z=53.1).\n11. Finish turn diameter Ø33.7 mm over length 36.0 mm (from Z=0.0 to Z=36.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01129
|
[
"images/Shaft_01129.png",
"detail_png/Shaft_01129_length.png",
"detail_png/Shaft_01129_diam.png",
"detail_png/Shaft_01129_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø61.4 mm and length at least 237.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø59.4 mm over length 122.3 mm (from Z=0.0 to Z=122.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø59.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø55.4 mm over length 49.1 mm (from Z=0.0 to Z=110.6).\n10. Finish turn diameter Ø51.5 mm over length 61.5 mm (from Z=0.0 to Z=61.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02486
|
[
"images/Shaft_02486.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 273.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 188.7 mm (from Z=0.0 to Z=188.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.7 mm over length 79.6 mm (from Z=0.0 to Z=79.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02923
|
[
"images/Shaft_02923.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø67.6 mm and length at least 70.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.6 mm over length 13.3 mm (from Z=0.0 to Z=13.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.1 mm over length 19.9 mm (from Z=0.0 to Z=51.7).\n9. Finish turn diameter Ø36.4 mm over length 22.9 mm (from Z=0.0 to Z=31.8).\n10. Finish turn diameter Ø30.0 mm over length 8.9 mm (from Z=0.0 to Z=8.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02903
|
[
"images/Shaft_02903.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø37.7 mm and length at least 235.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.7 mm over length 21.9 mm (from Z=0.0 to Z=21.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 208.7 mm (from Z=0.0 to Z=208.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00211
|
[
"images/Shaft_00211.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 317.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 199.0 mm (from Z=0.0 to Z=199.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.2 mm over length 113.6 mm (from Z=0.0 to Z=113.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01360
|
[
"images/Shaft_01360.png",
"detail_png/Shaft_01360_length.png",
"detail_png/Shaft_01360_diam.png",
"detail_png/Shaft_01360_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 206.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 78.9 mm (from Z=0.0 to Z=78.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.2 mm over length 122.8 mm (from Z=0.0 to Z=122.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01083
|
[
"images/Shaft_01083.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø55.6 mm and length at least 105.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.6 mm over length 36.0 mm (from Z=0.0 to Z=36.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø48.9 mm over length 7.5 mm (from Z=0.0 to Z=64.3).\n9. Finish turn diameter Ø40.6 mm over length 20.1 mm (from Z=0.0 to Z=56.8).\n10. Finish turn diameter Ø30.0 mm over length 36.7 mm (from Z=0.0 to Z=36.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04873
|
[
"images/Shaft_04873.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø55.4 mm and length at least 226.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.4 mm over length 109.6 mm (from Z=0.0 to Z=109.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.8 mm over length 44.8 mm (from Z=0.0 to Z=111.4).\n10. Finish turn diameter Ø32.8 mm over length 25.4 mm (from Z=0.0 to Z=66.6).\n11. Finish turn diameter Ø30.0 mm over length 41.2 mm (from Z=0.0 to Z=41.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01982
|
[
"images/Shaft_01982.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø48.7 mm and length at least 157.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.7 mm over length 45.8 mm (from Z=0.0 to Z=45.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 107.1 mm (from Z=0.0 to Z=107.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03631
|
[
"images/Shaft_03631.png",
"detail_png/Shaft_03631_length.png",
"detail_png/Shaft_03631_diam.png",
"detail_png/Shaft_03631_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø40.2 mm and length at least 217.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.2 mm over length 16.1 mm (from Z=0.0 to Z=16.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.7 mm over length 61.0 mm (from Z=0.0 to Z=196.5).\n10. Finish turn diameter Ø30.0 mm over length 135.5 mm (from Z=0.0 to Z=135.5).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00005
|
[
"images/Shaft_00005.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø33.8 mm and length at least 228.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø31.8 mm over length 22.4 mm (from Z=0.0 to Z=22.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø31.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 200.9 mm (from Z=0.0 to Z=200.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02193
|
[
"images/Shaft_02193.png",
"detail_png/Shaft_02193_length.png",
"detail_png/Shaft_02193_diam.png",
"detail_png/Shaft_02193_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø53.6 mm and length at least 203.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.6 mm over length 32.2 mm (from Z=0.0 to Z=32.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.6 mm over length 40.0 mm (from Z=0.0 to Z=166.7).\n10. Finish turn diameter Ø30.0 mm over length 126.7 mm (from Z=0.0 to Z=126.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04451
|
[
"images/Shaft_04451.png",
"detail_png/Shaft_04451_length.png",
"detail_png/Shaft_04451_diam.png",
"detail_png/Shaft_04451_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø79.8 mm and length at least 166.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.8 mm over length 42.4 mm (from Z=0.0 to Z=42.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø70.0 mm over length 14.1 mm (from Z=0.0 to Z=119.1).\n9. Finish turn diameter Ø59.6 mm over length 44.7 mm (from Z=0.0 to Z=105.0).\n10. Finish turn diameter Ø51.2 mm over length 60.3 mm (from Z=0.0 to Z=60.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02230
|
[
"images/Shaft_02230.png",
"detail_png/Shaft_02230_length.png",
"detail_png/Shaft_02230_diam.png",
"detail_png/Shaft_02230_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø46.8 mm and length at least 86.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.8 mm over length 5.0 mm (from Z=0.0 to Z=5.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø32.9 mm over length 13.0 mm (from Z=0.0 to Z=76.6).\n9. Finish turn diameter Ø30.0 mm over length 63.6 mm (from Z=0.0 to Z=63.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02935
|
[
"images/Shaft_02935.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø54.1 mm and length at least 319.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.1 mm over length 56.3 mm (from Z=0.0 to Z=56.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.6 mm over length 100.4 mm (from Z=0.0 to Z=258.2).\n10. Finish turn diameter Ø30.0 mm over length 157.8 mm (from Z=0.0 to Z=157.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00906
|
[
"images/Shaft_00906.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø78.9 mm and length at least 187.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.9 mm over length 25.9 mm (from Z=0.0 to Z=25.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.6 mm over length 44.8 mm (from Z=0.0 to Z=156.8).\n9. Finish turn diameter Ø44.5 mm over length 22.7 mm (from Z=0.0 to Z=112.0).\n10. Finish turn diameter Ø35.1 mm over length 16.1 mm (from Z=0.0 to Z=89.3).\n11. Finish turn diameter Ø30.5 mm over length 73.2 mm (from Z=0.0 to Z=73.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03654
|
[
"images/Shaft_03654.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø50.9 mm and length at least 219.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.9 mm over length 71.1 mm (from Z=0.0 to Z=71.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 143.8 mm (from Z=0.0 to Z=143.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01997
|
[
"images/Shaft_01997.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø81.1 mm and length at least 289.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.1 mm over length 100.5 mm (from Z=0.0 to Z=100.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø76.0 mm over length 55.7 mm (from Z=0.0 to Z=184.0).\n10. Finish turn diameter Ø59.6 mm over length 74.2 mm (from Z=0.0 to Z=128.3).\n11. Finish turn diameter Ø48.3 mm over length 54.1 mm (from Z=0.0 to Z=54.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04054
|
[
"images/Shaft_04054.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø76.5 mm and length at least 133.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.5 mm over length 54.5 mm (from Z=0.0 to Z=54.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø66.6 mm over length 30.2 mm (from Z=0.0 to Z=74.1).\n9. Finish turn diameter Ø50.4 mm over length 43.9 mm (from Z=0.0 to Z=43.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02123
|
[
"images/Shaft_02123.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø38.3 mm and length at least 75.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.3 mm over length 31.0 mm (from Z=0.0 to Z=31.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø32.5 mm over length 19.7 mm (from Z=0.0 to Z=39.6).\n9. Finish turn diameter Ø30.0 mm over length 19.9 mm (from Z=0.0 to Z=19.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04931
|
[
"images/Shaft_04931.png",
"detail_png/Shaft_04931_length.png",
"detail_png/Shaft_04931_diam.png",
"detail_png/Shaft_04931_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø35.8 mm and length at least 324.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.8 mm over length 103.3 mm (from Z=0.0 to Z=103.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 215.9 mm (from Z=0.0 to Z=215.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02589
|
[
"images/Shaft_02589.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø71.3 mm and length at least 86.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.3 mm over length 37.6 mm (from Z=0.0 to Z=37.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.0 mm over length 17.5 mm (from Z=0.0 to Z=44.0).\n9. Finish turn diameter Ø35.0 mm over length 26.5 mm (from Z=0.0 to Z=26.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02277
|
[
"images/Shaft_02277.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø68.1 mm and length at least 311.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø66.1 mm over length 79.7 mm (from Z=0.0 to Z=79.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø66.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø56.2 mm over length 44.1 mm (from Z=0.0 to Z=227.2).\n10. Finish turn diameter Ø47.9 mm over length 114.4 mm (from Z=0.0 to Z=183.1).\n11. Finish turn diameter Ø31.8 mm over length 68.7 mm (from Z=0.0 to Z=68.7).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04089
|
[
"images/Shaft_04089.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø80.8 mm and length at least 198.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.8 mm over length 82.6 mm (from Z=0.0 to Z=82.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø70.8 mm over length 65.7 mm (from Z=0.0 to Z=111.2).\n10. Finish turn diameter Ø54.8 mm over length 32.0 mm (from Z=0.0 to Z=45.5).\n11. Finish turn diameter Ø38.4 mm over length 13.5 mm (from Z=0.0 to Z=13.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01368
|
[
"images/Shaft_01368.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 312.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 179.1 mm (from Z=0.0 to Z=179.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø24.9 mm over length 128.7 mm (from Z=0.0 to Z=128.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00189
|
[
"images/Shaft_00189.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 286.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 227.8 mm (from Z=0.0 to Z=227.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.9 mm over length 53.4 mm (from Z=0.0 to Z=53.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03821
|
[
"images/Shaft_03821.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 280.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 153.0 mm (from Z=0.0 to Z=153.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.3 mm over length 122.8 mm (from Z=0.0 to Z=122.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03755
|
[
"images/Shaft_03755.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 153.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 113.6 mm (from Z=0.0 to Z=113.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.2 mm over length 34.5 mm (from Z=0.0 to Z=34.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01711
|
[
"images/Shaft_01711.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø52.8 mm and length at least 127.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.8 mm over length 34.3 mm (from Z=0.0 to Z=34.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø31.1 mm over length 46.3 mm (from Z=0.0 to Z=88.0).\n9. Finish turn diameter Ø30.0 mm over length 41.7 mm (from Z=0.0 to Z=41.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02216
|
[
"images/Shaft_02216.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø55.6 mm and length at least 205.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.6 mm over length 38.6 mm (from Z=0.0 to Z=38.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.6 mm over length 15.5 mm (from Z=0.0 to Z=161.5).\n10. Finish turn diameter Ø30.0 mm over length 146.0 mm (from Z=0.0 to Z=146.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01973
|
[
"images/Shaft_01973.png",
"detail_png/Shaft_01973_length.png",
"detail_png/Shaft_01973_diam.png",
"detail_png/Shaft_01973_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø63.0 mm and length at least 286.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.0 mm over length 87.8 mm (from Z=0.0 to Z=87.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø46.4 mm over length 23.6 mm (from Z=0.0 to Z=193.9).\n10. Finish turn diameter Ø30.0 mm over length 170.3 mm (from Z=0.0 to Z=170.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01490
|
[
"images/Shaft_01490.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø81.2 mm and length at least 214.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.2 mm over length 47.3 mm (from Z=0.0 to Z=47.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.0 mm over length 46.5 mm (from Z=0.0 to Z=162.1).\n10. Finish turn diameter Ø50.5 mm over length 31.6 mm (from Z=0.0 to Z=115.6).\n11. Finish turn diameter Ø42.1 mm over length 26.6 mm (from Z=0.0 to Z=84.0).\n12. Finish turn diameter Ø32.9 mm over length 20.6 mm (from Z=0.0 to Z=57.4).\n13. Finish turn diameter Ø30.0 mm over length 36.8 mm (from Z=0.0 to Z=36.8).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_04249
|
[
"images/Shaft_04249.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø46.9 mm and length at least 189.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.9 mm over length 81.2 mm (from Z=0.0 to Z=81.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.6 mm over length 81.2 mm (from Z=0.0 to Z=103.2).\n9. Finish turn diameter Ø30.0 mm over length 22.0 mm (from Z=0.0 to Z=22.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02783
|
[
"images/Shaft_02783.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø59.5 mm and length at least 301.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.5 mm over length 93.1 mm (from Z=0.0 to Z=93.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.4 mm over length 20.4 mm (from Z=0.0 to Z=203.1).\n10. Finish turn diameter Ø30.0 mm over length 182.7 mm (from Z=0.0 to Z=182.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02032
|
[
"images/Shaft_02032.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø63.6 mm and length at least 168.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.6 mm over length 34.8 mm (from Z=0.0 to Z=34.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø52.9 mm over length 65.4 mm (from Z=0.0 to Z=128.4).\n9. Finish turn diameter Ø41.3 mm over length 50.2 mm (from Z=0.0 to Z=63.0).\n10. Finish turn diameter Ø30.0 mm over length 12.8 mm (from Z=0.0 to Z=12.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03033
|
[
"images/Shaft_03033.png",
"detail_png/Shaft_03033_length.png",
"detail_png/Shaft_03033_diam.png",
"detail_png/Shaft_03033_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 243.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 115.9 mm (from Z=0.0 to Z=115.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø26.9 mm over length 122.3 mm (from Z=0.0 to Z=122.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01947
|
[
"images/Shaft_01947.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø48.8 mm and length at least 199.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.8 mm over length 51.0 mm (from Z=0.0 to Z=51.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø39.5 mm over length 45.5 mm (from Z=0.0 to Z=143.6).\n10. Finish turn diameter Ø35.5 mm over length 27.2 mm (from Z=0.0 to Z=98.1).\n11. Finish turn diameter Ø30.0 mm over length 70.9 mm (from Z=0.0 to Z=70.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_02152
|
[
"images/Shaft_02152.png",
"detail_png/Shaft_02152_length.png",
"detail_png/Shaft_02152_diam.png",
"detail_png/Shaft_02152_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø64.0 mm and length at least 218.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.0 mm over length 33.4 mm (from Z=0.0 to Z=33.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø56.8 mm over length 41.9 mm (from Z=0.0 to Z=179.7).\n10. Finish turn diameter Ø36.9 mm over length 43.8 mm (from Z=0.0 to Z=137.8).\n11. Finish turn diameter Ø33.4 mm over length 39.1 mm (from Z=0.0 to Z=94.0).\n12. Finish turn diameter Ø30.0 mm over length 54.9 mm (from Z=0.0 to Z=54.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_03166
|
[
"images/Shaft_03166.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø39.6 mm and length at least 156.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.6 mm over length 44.0 mm (from Z=0.0 to Z=44.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 107.2 mm (from Z=0.0 to Z=107.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02618
|
[
"images/Shaft_02618.png",
"detail_png/Shaft_02618_length.png",
"detail_png/Shaft_02618_diam.png",
"detail_png/Shaft_02618_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø79.8 mm and length at least 116.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.8 mm over length 19.6 mm (from Z=0.0 to Z=19.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.6 mm over length 23.8 mm (from Z=0.0 to Z=91.6).\n9. Finish turn diameter Ø56.5 mm over length 25.3 mm (from Z=0.0 to Z=67.8).\n10. Finish turn diameter Ø43.2 mm over length 29.7 mm (from Z=0.0 to Z=42.5).\n11. Finish turn diameter Ø40.2 mm over length 12.8 mm (from Z=0.0 to Z=12.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_02314
|
[
"images/Shaft_02314.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø53.9 mm and length at least 317.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.9 mm over length 24.2 mm (from Z=0.0 to Z=24.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.9 mm over length 31.6 mm (from Z=0.0 to Z=288.5).\n10. Finish turn diameter Ø30.0 mm over length 256.9 mm (from Z=0.0 to Z=256.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01568
|
[
"images/Shaft_01568.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø63.8 mm and length at least 78.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø61.8 mm over length 19.8 mm (from Z=0.0 to Z=19.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø61.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø43.1 mm over length 12.7 mm (from Z=0.0 to Z=53.9).\n9. Finish turn diameter Ø38.5 mm over length 12.4 mm (from Z=0.0 to Z=41.2).\n10. Finish turn diameter Ø30.0 mm over length 28.8 mm (from Z=0.0 to Z=28.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03757
|
[
"images/Shaft_03757.png",
"detail_png/Shaft_03757_length.png",
"detail_png/Shaft_03757_diam.png",
"detail_png/Shaft_03757_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø45.4 mm and length at least 316.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.4 mm over length 45.7 mm (from Z=0.0 to Z=45.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø37.0 mm over length 95.0 mm (from Z=0.0 to Z=266.1).\n10. Finish turn diameter Ø30.7 mm over length 49.5 mm (from Z=0.0 to Z=171.1).\n11. Finish turn diameter Ø30.0 mm over length 121.6 mm (from Z=0.0 to Z=121.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04212
|
[
"images/Shaft_04212.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø69.5 mm and length at least 310.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.5 mm over length 55.4 mm (from Z=0.0 to Z=55.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.2 mm over length 66.3 mm (from Z=0.0 to Z=250.0).\n10. Finish turn diameter Ø47.7 mm over length 86.3 mm (from Z=0.0 to Z=183.7).\n11. Finish turn diameter Ø41.3 mm over length 97.4 mm (from Z=0.0 to Z=97.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01556
|
[
"images/Shaft_01556.png",
"detail_png/Shaft_01556_length.png",
"detail_png/Shaft_01556_diam.png",
"detail_png/Shaft_01556_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø71.3 mm and length at least 113.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.3 mm over length 22.6 mm (from Z=0.0 to Z=22.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.6 mm over length 19.5 mm (from Z=0.0 to Z=85.8).\n9. Finish turn diameter Ø49.9 mm over length 6.3 mm (from Z=0.0 to Z=66.3).\n10. Finish turn diameter Ø35.1 mm over length 13.2 mm (from Z=0.0 to Z=60.0).\n11. Finish turn diameter Ø30.0 mm over length 46.8 mm (from Z=0.0 to Z=46.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03252
|
[
"images/Shaft_03252.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø65.8 mm and length at least 154.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.8 mm over length 6.8 mm (from Z=0.0 to Z=6.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.4 mm over length 23.4 mm (from Z=0.0 to Z=142.4).\n10. Finish turn diameter Ø32.4 mm over length 18.2 mm (from Z=0.0 to Z=119.0).\n11. Finish turn diameter Ø30.0 mm over length 100.8 mm (from Z=0.0 to Z=100.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01160
|
[
"images/Shaft_01160.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø47.2 mm and length at least 322.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.2 mm over length 74.4 mm (from Z=0.0 to Z=74.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø41.2 mm over length 63.9 mm (from Z=0.0 to Z=243.5).\n10. Finish turn diameter Ø30.0 mm over length 179.6 mm (from Z=0.0 to Z=179.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04160
|
[
"images/Shaft_04160.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.0 mm and length at least 73.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.0 mm over length 8.6 mm (from Z=0.0 to Z=8.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.1 mm over length 8.6 mm (from Z=0.0 to Z=60.1).\n9. Finish turn diameter Ø47.3 mm over length 9.0 mm (from Z=0.0 to Z=51.5).\n10. Finish turn diameter Ø32.2 mm over length 5.0 mm (from Z=0.0 to Z=42.5).\n11. Finish turn diameter Ø30.0 mm over length 37.5 mm (from Z=0.0 to Z=37.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03119
|
[
"images/Shaft_03119.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø34.4 mm and length at least 146.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.4 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 127.9 mm (from Z=0.0 to Z=127.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01480
|
[
"images/Shaft_01480.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø47.0 mm and length at least 107.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø45.0 mm over length 16.5 mm (from Z=0.0 to Z=16.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø45.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø41.5 mm over length 13.8 mm (from Z=0.0 to Z=85.9).\n9. Finish turn diameter Ø30.6 mm over length 25.9 mm (from Z=0.0 to Z=72.1).\n10. Finish turn diameter Ø30.0 mm over length 46.2 mm (from Z=0.0 to Z=46.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01742
|
[
"images/Shaft_01742.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 178.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 98.5 mm (from Z=0.0 to Z=98.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.9 mm over length 75.3 mm (from Z=0.0 to Z=75.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00986
|
[
"images/Shaft_00986.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø74.4 mm and length at least 190.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø72.4 mm over length 80.7 mm (from Z=0.0 to Z=80.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø72.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.5 mm over length 53.9 mm (from Z=0.0 to Z=105.0).\n9. Finish turn diameter Ø54.4 mm over length 51.1 mm (from Z=0.0 to Z=51.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00474
|
[
"images/Shaft_00474.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø44.4 mm and length at least 275.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.4 mm over length 34.4 mm (from Z=0.0 to Z=34.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.1 mm over length 87.0 mm (from Z=0.0 to Z=236.3).\n10. Finish turn diameter Ø30.0 mm over length 149.3 mm (from Z=0.0 to Z=149.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04470
|
[
"images/Shaft_04470.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 239.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 170.0 mm (from Z=0.0 to Z=170.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.4 mm over length 64.9 mm (from Z=0.0 to Z=64.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00880
|
[
"images/Shaft_00880.png",
"detail_png/Shaft_00880_length.png",
"detail_png/Shaft_00880_diam.png",
"detail_png/Shaft_00880_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø75.6 mm and length at least 86.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.6 mm over length 7.9 mm (from Z=0.0 to Z=7.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø61.2 mm over length 19.6 mm (from Z=0.0 to Z=73.6).\n9. Finish turn diameter Ø44.5 mm over length 14.4 mm (from Z=0.0 to Z=54.0).\n10. Finish turn diameter Ø30.5 mm over length 19.4 mm (from Z=0.0 to Z=39.6).\n11. Finish turn diameter Ø30.0 mm over length 20.2 mm (from Z=0.0 to Z=20.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00176
|
[
"images/Shaft_00176.png",
"detail_png/Shaft_00176_length.png",
"detail_png/Shaft_00176_diam.png",
"detail_png/Shaft_00176_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 70.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 44.8 mm (from Z=0.0 to Z=44.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø28.8 mm over length 20.8 mm (from Z=0.0 to Z=20.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_03538
|
[
"images/Shaft_03538.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø40.5 mm and length at least 229.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.5 mm over length 68.9 mm (from Z=0.0 to Z=68.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 155.6 mm (from Z=0.0 to Z=155.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02042
|
[
"images/Shaft_02042.png",
"detail_png/Shaft_02042_length.png",
"detail_png/Shaft_02042_diam.png",
"detail_png/Shaft_02042_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø70.2 mm and length at least 290.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.2 mm over length 50.6 mm (from Z=0.0 to Z=50.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø62.8 mm over length 140.6 mm (from Z=0.0 to Z=235.0).\n10. Finish turn diameter Ø57.6 mm over length 72.8 mm (from Z=0.0 to Z=94.4).\n11. Finish turn diameter Ø50.1 mm over length 21.6 mm (from Z=0.0 to Z=21.6).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03681
|
[
"images/Shaft_03681.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø35.1 mm and length at least 274.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.1 mm over length 12.4 mm (from Z=0.0 to Z=12.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 256.8 mm (from Z=0.0 to Z=256.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Subsets and Splits
No community queries yet
The top public SQL queries from the community will appear here once available.